No products in the cart.
menu
Categories
- Arduino
- Raspberry Pi
- MICRO:BIT - EDUSTEM
-
Robotica Domotica
- Meccanica
- Servomotori
- Schede
- Accessori
-
Sensori
- Sensori vari
- Sensori ad ultrasuoni
- Sensori di posizione
- Sensori ad infrarossi
- Sensori di temperatura
- Sensori di umidità
- Sensori di luminosità
- Sensori di Gas ed Alcool
- Sensori di contatto
- Sensori di suono
- Sensori di colore
- Sensori Real Time Clock
- Set di sensori
- Sensori di vento
- Sensori magnetici
- Sensori biometrici
- Sensori Wearable
- Laser
- sensori/trasmettitori di pressione
- Optikascience
- Motori
- Batterie
- Carica batterie
- Attrezzatura
- Prototipazione elettronica
- Pannelli solari
- ACCESSORI DA LABORATORIO
- ATLAS SCIENTIFIC - ENVIROMENTAL ROBOTICS
- ACTUONIX
- Elettronica low cost
- NT sensor
- PLUX
- CNC - Plotter
-
3D Printer & Scanner
- Officine Robotics
- Scanner 3D
- SCUOLA - MEPA
- Robot Kit
- Taglio Laser
- IoT - Smart Home
- AI & Machine Learning
- blog
- Home
-
- 3D Printer & Scanner
- AI & Machine Learning
- Arduino
- CNC - Plotter
- Display
- IoT - Smart Home
- MICRO:BIT - EDUSTEM
- Officine Robotics
- Raspberry Pi
- Robot Kit
- Robotica Domotica
- Accessori
- ACCESSORI DA LABORATORIO
- ACTUONIX
- ATLAS SCIENTIFIC - ENVIROMENTAL ROBOTICS
- Attrezzatura
- Batterie
- Carica batterie
- Elettronica low cost
- Meccanica
- Motori
- NT sensor
- Pannelli solari
- PLUX
- Prototipazione elettronica
- Schede
- Sensori
- Laser
- Optikascience
- Sensori ad infrarossi
- Sensori ad ultrasuoni
- Sensori biometrici
- Sensori di colore
- Sensori di contatto
- Sensori di Gas ed Alcool
- Sensori di luminosità
- Sensori di posizione
- Sensori di suono
- Sensori di temperatura
- Sensori di umidità
- Sensori di vento
- Sensori magnetici
- Sensori Real Time Clock
- Sensori vari
- Sensori Wearable
- sensori/trasmettitori di pressione
- Set di sensori
- Servomotori
- SCUOLA - MEPA
- Taglio Laser
- 3D Printer & Scanner
Idee Regalo
-
Buoni Regalo
Offerta Gift Card 20€- 50€- 100€ Regala un buono -
Corsi Arduino-3D Printer
Arduino Micro:Bit Raspberry Robot Marttino
Nuovi prodotti
controllo-motori
General Driver board...KY-008 650NM 5V LASER MODULE
This 100mW laser module emits a small intense focused beam of visible red light. The example provided below shows how the module can be used with an Arduino and photo resistor module (available here) to perform basic remote signaling.
This 100mW laser module emits a small intense focused beam of visible red light. The example provided below shows how the module can be used with an Arduino and photo resistor module (available here) to perform basic remote signaling.
Warning: This is a low power laser device, however as with all laser devices care should be taken when in use. You should never look directly in to its beam or point the laser at another person. Doing so may cause permanent eye damage. This item is not suitable for children.
Item Code: HCMODU0104
Operating voltage: 5V
Max Current (Laser on): ~30mA
PINOUT
1 – GND
2 – 5V
3 – S (Control: HIGH = Laser on);
This module can be purchased here.
The connection diagram below is for use with the transmit sketch.
Example Arduino sketches available on our support forum here.